Hash Rate: 12.5TH/s ±5%. Power Consumption: 1576W ±7% at the wall (with Bitmain's APW3 PSU, 93 percent efficiency, 25C ambient temp). Power Efficiency: 0.126 J/GH at the wall (with Bitmain's APW3 PSU). Noise level: Loud. Chip quantity per unit: 171 x BM1387. Rated Voltage: 11.60 ~13.00V. Operating Temperature: 0C to 40C. Network Connection: Ethernet (cable not included). Notes: 1. Each AntMiner T9 has three 6-pin PCI-e connectors for 12V/15A DC STABLE input for the three hash boards and one additional 6-pin PCI-e connector on the controller. All TEN 6-pin PCI-e connectors are required. Do not connect more than one PSU to the same hash board to prevent possible damage and instability. 2. Power consumption figures will vary with your PSU's efficiency, the ambient operating temperature and the accuracy of the power meter. 3. Power supply unit is not included. The APW3 power supply is recommended if you have the required 205-264v, otherwise use the EGCA 1600 G2.
S3+ Specifications: Hash Rate: 453 GH/s±10% Power Consumption: 355 Watt at the wall Power Efficiency: 0.78J/GH on wall Power Supply: 12V DC Size: 331 mm x 137 mm x 160 mm Fans: Two 14038 fans mounted on both front and back ends Operating Temperature: 0 °C to 35 °C Complied with: FCC / CE Network Connection: Ethernet Power consumption: This figure depends on the PSU efficiency, ambient temperature and the accuracy of the power meters. Features: Stand alone: The S3+ mines stand alone, needs no proxy server or a separate computer. (no need of Rpi or Beagle Bone Black or Cubie Board) Quiet: The customized heat sinks mounted to the hash boards, one box over S3+ to control the air flow, two fans mounted on both front and back ends that mean fans are able to work at lower speed to dissipate all heat easily. This design let S3+ run at much lower noise level. Stable: Running 24 hours a day with minimal downtime. Accurate: Hardware Error rate from the sample unit is as low as 0.01%, hundreds times better than some competing products. Efficient: High energy efficiency to save your investment on PSU and electricity bills. Notes: 1) Power consumption: This figure depends on the PSU efficiency, ambient temperature and the accuracy of the power meters. 2) PSU: You have to prepare your own the ATX PSU. The S3+ ships without a Power Supply Unit. There are 4 PCI-e connectors for +12V DC input, but it only needs to connect two of them. Don't parallel connected different DC input from different PSU into the same Hashing board. OVER CLOCKING, MODIFYING CONFIGURATION INACCESSIBLE FROM THE WEB CONTROL PANEL VOIDS WARRANTY
The Bitmain AntMiner S3 is the best value of any Bitcoin miner currently on the market. While other manufacturers ask you to wait indefinitely for preorders which may never come, Bitmain has been delivering consistently for months. The AntMiner S3 offers users one of the easiest setup experiences of any Bitcoin miner. Just plug it in, configure its IP address, enter your mining pool information, and it will do the rest. You can have your S3 units up and running within minutes of receiving them.
The APW3++ can deliver a maximum power of only 1200W if it is connected to a 110V mains power supply. To obtain the rated power of 1600W, the APW3++ must be connected to a 220-240V mains power supply. Please check the mains power supply that is the standard in your region before ordering.
1. Specifications of the Antminer D3 are as follows: a) Hash rate: 15 GH/s (Variation of ±5% is expected) b) Power consumption: 1200W (at the wall, with Bitmain's APW3 PSU, 93% efficiency, 25°C ambient temp). c) Dimensions of the miner: 320*130*190mm d) Hashing algorithm: X11